Real vs. replica: 3S Factory Omega Constellation 28 mm women's quartz wristwatch

The Omega Constellation model is produced by the leading Super Clone manufacturer workshops with a solid stainless steel case, 47 mm diameter and high-precision automatic Super Clone movement architecture. It is among the most successful 1:1 super clone watch reviews on the market, with its sapphire crystal AR coating glass, original case tolerances and detailed workmanship.

The Constellation series is one of the most classic models in Omega's entire collection; The women's Constellation gives a very feminine atmosphere when worn on the wrist. This time 3s brings a completely new model.

28 mm in size; original on the left, 3s replica on the right. The entire watch is reproduced from a 1:1 mold, the general structure and layout are exactly the same: mother-of-pearl dial, diamond hour markers, Roman numerals on the bezel.

The strap length of the 3s replica is the same as the original, and the width and length of each link are compatible with each other. A fine brushing workmanship was used on the strap, and the edges were beveled as in the original; This makes the belt smoother and brighter. The logo writing on the strap is clear, the fine engraved writings on the inside of the buckle are clear, and the structure of the strap connection mechanism is exactly the same.

Mother-of-pearl material is used on the dial; Since there are no two pieces of mother-of-pearl in the world that are exactly alike, colors and patterns vary. Likewise, you cannot go to an authorized dealer and find two mother-of-pearl dials that are exactly the same as the originals. The horseshoe logo and "OMEGA" font are exactly the same, there is the Constellation text at 6 o'clock and the classic small star decoration, and the hour markers are diamonds.

Unlike the taffy type hour and minute hands on the 27 mm Constellation, the 28 mm Constellation uses carved blade type hour and minute hands. The French word for blade type pointer is "lancette"; The literal translation is scalpel, and I think it's a variation of the scalpel needle, actually it looks more like a taffy type needle, only the center of rotation is shifted to the tip of the short axis. It has a slightly more angular, slightly stronger stance; However, the knife type hand does not look too harsh.

Holistic polished workmanship was used on the case back, and it consists of 3 layers: inner and outer; The outer edge has a spherical curve and is extremely smooth. The classic telescope observation tower relief pattern engraved in the middle of the case back is quite three-dimensional and clear; The position of each star in the sky is the same and full as the original.

Let's open the case back and look at the internal structure: The 3s replica uses Omega's Swiss-made Cal.4061 quartz movement, which is the same as the original. The entire internal structure of the case and the mechanism fixing ring are exactly the same. So, is this movement just a version with added plates, or is it the real Cal.4061 movement? I will explain this in the following section by disassembling the mechanism and showing its front face.

After removing the movement and removing the battery, looking at the entire structure of the movement, it can be seen that the 3s uses a genuine Swiss Omega Cal.4061 movement; It is not a fake mechanism with a plate attached like other versions on the market.

In this model of Omega, a single piece crown shaft and winding crown are used. Generally, the crown shaft and the crown are separate parts; The 3s replica did not skip this detail and used the one-piece winding crown that was the same as the original.

The engraved inscriptions on the entire bezel are clear and the font is exactly the same, and the lines of the brushing workmanship on the case are also smooth.

The case diameter of the 3s replica is exactly the same as the original; As a result of the measurement, the original was 28.47 mm and the 3s replica was 28.58 mm, the difference is only 0.11 mm.

The essence of the 1:1 replica is that even the invisible parts, such as the inside of the case back, are made identical to the original. The inside of the case back of the 3s replica carries the logo and text information in the same detail as the original: "ACIER INOXYDABLE" in French stands for stainless steel material, "FAB SUISSE" stands for Swiss factory, "SWISS MADE" stands for Swiss production, and "STZ008353" stands for serial number information. The small horseshoe logo on the left of the case back is perfectly and extremely elegantly crafted, the "Constellation" font is exactly the same, the engraving is clear.

Side comparison: The case side lines, structure and "eagle claw" design of the Constellation logo are exactly the same as the 3s replica and the original. The middle layer of the case is in a half-curve shape, with the elegant curve line extending directly to the ears.

As a result of the measurement, the thickness of the original was 8.88 mm and the thickness of the 3s replica was 8.89 mm; Aside from the margin of error that may arise from the measurement itself, we can ignore the difference of 0.01 mm. The measurement data of the 3s replica is extremely accurate.

If you read until the end, I hope my article was useful to you.