What has been improved on the ZZ Factory V3 edition Rolex green water ghost?

The Rolex Submariner model is produced by ZZ Factory with a high-tech ceramic case, 41 mm diameter and ETA 2836-2 caliber in Swiss norms architecture. It is among the most successful 1:1 super clone watch reviews on the market, with its sapphire crystal AR coating glass, original case tolerances and detailed workmanship.

3135/3130/2836 (black/green) versions have all been upgraded; ZZ cooperates with clean (clean end fitting + ar belt) factory to launch the water ghost with a steel bracelet. Black hole watch glass: The brightness and light transmittance of sapphire in the magnifying glass in 3 positions has been increased to the maximum. The transition between the glass and the ceramic bezel is more natural; The edge R corner of the glass was produced by remeasured. This upgrade completely solved the feel problem of the steel bracelet; Negotiations were made with the AR steel bracelet factory for months, and repeated attempts were made to resolve the compatibility of the step curve of the end fitting and the case. In my opinion, only products with 'equal' step difference in the four corners range of 0.13-0.15 mm can be called the most perfect water ghost.

The difference in each corner is kept within the range of 0.13-0.15 mm; because mechanical processing itself has a margin of error. This is the shipping standard of the ZZ V3. It cannot be greater than 0.15, nor less than 0.13.

The brightness and transparency of the sapphire loupe have been increased; Made a slight improvement over V2S. But obviously, there is the black hole effect; However, there is a slight difference compared to the original - and this is something I say from a meticulous perspective.

The edge of the glass and the R corner were remeasured, aiming for an effect that was as consistent as possible with the original. Of course, the recessed (collapsed) appearance of the glass was still preserved.

That meant all non-standard fittings; Using the same mold, the curvature and height difference of all of them were checked for fit. Perhaps this detail, which is inconspicuous in the eyes of others, can be an important basis for distinguishing between the real thing and the replica. Plump (filled) middle body, machined connection pins... ZZ pays attention to every detail. Maybe you can't imagine it, but just this one 'equal' step took more than half a year to be developed and put into production. It's not that we don't want to do well the first time; We just notice the problem during the sales process and fix it.

The buckle code of ZZ V3 version has been changed to '1LD'. As for the clean green bezel issue: starting about half a year ago, we can say that the clean green bezel is a groundbreaking product and a milestone progress in the field of replica. We cannot say for sure that the Clean 3 green bezel is the best; We just have to compare it with the color of the original when making the comparison. In the process of comparing with the original, we can say without exaggeration that the green bezel of the Clean is relatively close. Do not make a mistake and compare whose color is darker or lighter; After all, what is referenced is the original, not imagining something darker and greener than the original. Will it be more original than the original? I believe that a good part should meet more factories and customers; We are now in the 21st century, that understanding of monopoly does not fit the age. I hope clean will go better and longer and serve a wide audience of watch enthusiasts; It's not ZZ who profits from this, because clean's attitude is always neutral. Neither to one side nor to the other. The blue coating has not been a criterion for distinguishing between real and replica for a long time; In fact, on near-original water phantoms, the magnifier's blue coating is barely visible, and even if there is a slight coating, it naturally flakes off after a few months of use — including the new 41 mm water phantom I received recently. I hope the factory pays more attention to the instantaneous changes in the details of the original when making a statement. After all, some statements have a certain authority as a factory; Trying not to mislead the customer makes the job look more professional. ZZ cooperates with the clean (clean end fitting / ar belt) factory to launch the water ghost with a steel bracelet, perfectly displaying the 0.13 mm step (height difference between the case and the connecting part of the strap; equal 0.13 mm step on all four corners). Each strap has a specific pattern to match; The same is true for the safe. The clean belt is solely responsible for adjusting the parameters of the end link piece on the basis of the steel bracelet, adapting it to the ZZ chassis and producing the step that has not been surpassed for years. (Let's point out that having steps is not a rare thing in the water ghost market; however, the issue here is the 'equal' step of 0.13-0.15 mm. It is not really easy to do this equally in all four corners. This time, getting the cooperation of the Ar steel bracelet contract factory is the result of many meetings. It must be admitted that the Ar steel bracelet is truly the highest level, first-class quality in the market.)

Below are high-definition real shot photos of the ZZ Factory V3 green water ghost.